
INFINISIL Spec Grade Performance Silicone
INFINISIL Spec Grade Performance Silicone is designed to be used in applications where higher physical properties and lower compression set are required.
It is resistant to extreme high and low temperature ranges and is proven to be an excellent gasketing material. Meets the A-A-59588 specification which supersedes ZZ-R-765. Made in the USA.
Color: Red (other colors available)
Samples available upon request.

Temperature Range: | -80°F to +450°F |
Durometer Range (Shore A ± 5): | 40 to 70 |
Tensile (min. psi.): | 725 |
Elongation Range (min. %): | 150 to 300 |
Finishes Available: | Smooth, Nylon |
Talc: | Talc-Free Available |
Specification: | A-A-59588 2A & 2BAMS 3301 ASTM D 2000 M1GE |
We comply with the Buy American Act requirements.
Compound Numbers: 040S0561, 050S0562, 060S0563, 070S0564
Unsure on how to read our compound number? Read the page, “How to Read a Compound Number”.
Molded Sheet Size: 36″ x 36″ , 48″ x 48″
Trim: Untrimmed
Stock Item Minimum: One Foot
Non Stock Item Minimum: Please Contact Us For Minimums & Availability
Rubber Roll Width
Standard WARCO Sheet rubber rolls are untrimmed and can measure approximately 3” in additional width. Trimmed rolled rubber is provided either 36”, 48” or 55” wide ± 1”
Custom widths are available, please call for details.
Rubber Roll Lengths
Standard Roll approximate length ±10%. Products may vary, please see product listing for standard roll lengths.
Sheet Roll Lengths:
- 1/64″ thick – 180 feet
- 1/32” thick – 150 feet
- 1/16” thick – 100 feet
- 3/32” thick – 65 feet
- 1/8” thick – 50 feet
- 3/16” thick – 30 feet
- 1/4” thick – 25 feet
- 5/16” thick – 20 feet
- 3/8” thick – 16.5 feet
- 1/2” thick – 12.5 feet
Sheet Rubber Thickness Tolerances
Closer tolerances and Custom thicknesses are available and can be priced on request.
WARCO Thickness Tolerance – Standard RMA
- 0.031” & thinner: ± 0.010″
- 0.032″ to 0.061″: ± 0.012″
- 0.062″ to 0.124″: ± 0.016″
- 0.125″ to 0.186″: ± 0.020″
- 0.187″ to 0.374″: ± 0.031″
- 0.375″ to 0.500″: ± 0.047″
- 0.501″ to 0.750″: ± 0.094″
- 0.751″ & thicker: ± 10%
Sheet Rubber Finish
Unless otherwise noted, sheet rubber has a standard smooth finish. Textured (fabric) finish and matte finish are available on most materials at an additional cost. Please call for details.
Sheet Rubber Color
This product is red as opposed to the standard color of our sheet rubber, black. Custom colors and color matching is available.
Test Reports
Short form test results, basic physicals, are available upon request at the time of the order. Full test reports for particular specifications will be also quoted on request. This may include certifying the ozone resistance, heat ageing, compliances, and many more aspects of our product. Certifications are sent with your order upon request at no charge.
More information about the WARCO products is available at General Product Information.
INFINISIL® is a registered trademark of West American Rubber Company, LLC. All text containing the word “INFINISIL” is trademarked by West American Rubber Company, LLC regardless of whether the ® mark or ™ mark is attached or not.
Our rubber products are a proprietary blend of various polymers formulated to meet stated physicals and specifications. The named product polymer is not necessarily the primary polymer representing the highest percentage of the polymer blend. Determination of the suitability of the goods for the uses and applications contemplated by Buyer and others shall be the sole responsibility of the Buyer or user. No guaranty is given with respect to length of service on any particular application. Suggestions or recommendations made by Seller in its product literature concerning uses or applications of the goods are believed to be reliable, but Seller makes no warranty or guaranty of results to be obtained since the conditions of the use and application by Buyer and others are beyond Seller’s control. The specification listed here, SAE AMS, stands for the Society of Automotive Engineers International Aerospace Material Specifications, a global association of engineers and related technical experts in the aerospace, automotive, and commercial-vehicle industries. Their website can be found here: https://www.sae.org/publications/collections/content/dlibstd-ams. The specification listed here, ASTM, stands for the American Society for Testing and Materials which is the developer and provider of voluntary consensus standards, related technical information, and services. Their website can be found here: https://www.astm.org/.
View complete Terms & Conditions of Sale for suitability of use and formulations