Cloth Inserted Neoprene – Regular Cotton Ply
Cloth Inserted Neoprene – Regular Cotton Ply is a blended Neoprene compound with one or more cotton fabric plies, for service where dimensional stability is required.
Suitable for use where moderate oil resistance is required and where hot and cold water and gases are being conveyed. Fabric content per thickness is one ply for 1/32” and 1/16”, two plies for 1/8”, three plies for 3/16”, and four plies for 1/4”. Made in the USA.
Samples available upon request.
| Temperature Range: | -30°F to +200°F |
| Durometer (Shore A ± 5): | 70 |
| Tensile (typical psi.): | 1000 |
| Elongation (typical %) | n/a |
| Finishes Available: | Smooth, Nylon |
| Talc: | Talc-Free Available |
| Primary Feature: | Made in the USA |
We comply with the Buy American Act requirements.
*Physicals presented are typical value – we certify to the minimum value.
† Durometer and tensile strength of the above material is calculated with the respective material inserted into the sheet.
GAUGES: This construction includes one ply for each 1/16” thickness:
1/16 – 3/32 = 1 ply; 1/8” = 2 plies; 3/16” = 3 plies; 1/4” = 4 plies
Compound Number: 070E1162
Unsure on how to read our compound number? Read the page, “How to Read a Compound Number”.
Rubber Roll Width
Standard WARCO Sheet rubber rolls are untrimmed and can measure approximately 3” in additional width. Trimmed rolled rubber is provided either 36”, 48” or 55” wide ± 1”
Custom widths are available, please call for details.
Rubber Roll Lengths
Standard Roll approximate length ±10%. Products may vary, please see product listing for standard roll lengths.
Sheet Roll Lengths:
- 1/64″ thick – 180 feet
- 1/32” thick – 150 feet
- 1/16” thick – 100 feet
- 3/32” thick – 65 feet
- 1/8” thick – 50 feet
- 3/16” thick – 30 feet
- 1/4” thick – 25 feet
- 5/16” thick – 20 feet
- 3/8” thick – 16.5 feet
- 1/2” thick – 12.5 feet
Sheet Rubber Thickness Tolerances
Closer tolerances and Custom thicknesses are available and can be priced on request.
WARCO Thickness Tolerance – Standard RMA
- 0.031” & thinner: ± 0.010″
- 0.032″ to 0.061″: ± 0.012″
- 0.062″ to 0.124″: ± 0.016″
- 0.125″ to 0.186″: ± 0.020″
- 0.187″ to 0.374″: ± 0.031″
- 0.375″ to 0.500″: ± 0.047″
- 0.501″ to 0.750″: ± 0.094″
- 0.751″ & thicker: ± 10%
Sheet Rubber Finish
Unless otherwise noted, sheet rubber has a standard smooth finish. Textured (fabric) finish and matte finish are available on most materials at an additional cost. Please call for details.
Sheet Rubber Color
The standard color of our sheet rubber is black, unless noted otherwise. Custom colors and color matching is available.
Test Reports
Short form test results, basic physicals, are available upon request at the time of the order. Full test reports for particular specifications will be also quoted on request. This may include certifying the ozone resistance, heat ageing, compliances, and many more aspects of our product. Certifications are sent with your order upon request at no charge.
More information about the WARCO products is available at General Product Information.
Our rubber products are a proprietary blend of various polymers formulated to meet stated physicals and specifications. The named product polymer is not necessarily the primary polymer representing the highest percentage of the polymer blend. Determination of the suitability of the goods for the uses and applications contemplated by Buyer and others shall be the sole responsibility of the Buyer or user. No guaranty is given with respect to length of service on any particular application. Suggestions or recommendations made by Seller in its product literature concerning uses or applications of the goods are believed to be reliable, but Seller makes no warranty or guaranty of results to be obtained since the conditions of the use and application by Buyer and others are beyond Seller’s control.
View complete Terms & Conditions of Sale for suitability of use and formulations
